Daiwa Millionaire Proteus 300 Servicing and Upgrading Part 6: The DIY Mono Mag | FishingAdvNHF

CLICK HERE TO SUBSCRIBE

    After the Daiwa Millionaire Proteus 300 was serviced and lubricated, the next step is to upgrade the reel with the DIY Mono Mag as requested by my friend.

**Share this video by copying this link

**Watch my trip at Air Papan Beach with the Bait Launcher here

**Subscribe now by clicking this link

**Check out my other videos by clicking this link

    This DIY Mono Mag require very few parts, the most important part being the Rare Earth Magnet. I bought them few years ago when I was trying out the Magnetic Coupling for my DIY Electric Trolling Motor project, which was failed eventually. I gathered the necessary parts as follow,

1) 8mm stainless steel bolt x 1
2) 8mm stailess steel Nut   x 1
3) Rare Earth Magnet (6mm OD) x 4
4) Wheel Air Inlet Cap   x 1
5) Coil Spring (Customary)   x 1

    Basic tools required and some Epoxy paste was used and it took around 3 hours to complete the project. (not including the drying time for the Epoxy)

    As usual, mistakes were made and I had to do some amendment. However, the project was completed and the reel was on time for the Pulau Ubin fishing trip.

==============================­­========­==­­=====
Please give me your valuable comments to help me making improvement and click the LIKE and SHARE if you find the video is good. Subscribe to my channel for the latest update on the new videos.

You can reach me @

NorthernHardcoreFisherman @ Google+

NorthernHardcoreFisherman @ Facebook

NorthernHardcoreFisherman @ Instagram

NorthernHardcoreFisherman @ Twitter

NorthernHardcoreFisherman @ Tumblr

==============================­­========­==­­=====
Always Tight Line, Hardcore is the Spirit!

Read More

Daiwa Millionaire Proteus 300 Servicing and Upgrading Part 5: The Completion | FishingAdvNHF

CLICK HERE TO SUBSCRIBE

    As soon as I have done the Bearing servicing cum repair, I proceeded on on the cleaning of the gear parts that I removed. Many had dried grease and dirt stuck on them but with the help of some petrol and WD40, some Autosol as well, I managed to got them all clean up.

**Share this video by copying this link

**Watch my trip at Air Papan Beach with the Bait Launcher here

**Subscribe now by clicking this link

**Check out my other videos by clicking this link

    All parts were put back and new grease was apply on each moving mechanism. I made full use of the Rocket Fuel Red Label that I bought few years ago. It was used on the moving part and on the Drag system as well.

    The assembly was easy and the result is marvelous, cranking is extremely smooth without any resistance felt, the spool spin freely with no loud noise. It's near perfect servicing and the Daiwa is ready for the next stage.

    Up next in part 6 I will be installing the DIY Mono Mag onto the Daiwa Millionaire Proteus 300, stay tuned.

==============================­­========­==­­=====
Please give me your valuable comments to help me making improvement and click the LIKE and SHARE if you find the video is good. Subscribe to my channel for the latest update on the new videos.

You can reach me @

NorthernHardcoreFisherman @ Google+

NorthernHardcoreFisherman @ Facebook

NorthernHardcoreFisherman @ Instagram

NorthernHardcoreFisherman @ Twitter

NorthernHardcoreFisherman @ Tumblr

==============================­­========­==­­=====
Always Tight Line, Hardcore is the Spirit!

Read More

Daiwa Millionaire Proteus 300 Servicing and Upgrading Part 4: Ultimate Bearing Servicing | FishingAdvNHF

CLICK HERE TO SUBSCRIBE

    After the Bearing was removed, I found that it is wearing out. The thought of have the bearing replaced was not materialized as the inventories that I have don't have the same size as the one on the Daiwa Millionaire Proteus 300.

**Share this video by copying this link

**Watch my trip at Air Papan Beach with the Bait Launcher here

**Subscribe now by clicking this link

**Check out my other videos by clicking this link

    I decided to go a step further and did the Ultimate Bearing Servicing that I had learned from a fishing blog many years ago. I did the trick onto my Abu Garcia's Bearing and it's performance was greatly improved.

     The trick is to remove the Dust Cover of the Bearing and have the Ball Bearing inside cleaned. To do this the Retaining Clip on the Bearing have to be removed using a Needle. Carefully pry out the tiny Retaining Spring and lift up the Dust Cover with the help of that same Needle.

    I skipped a few steps to save some time, in actual servicing the Ball Bearing can be pushed out and the Bearing Housing can be cleaned inside out. All parts should be soaked in Cleaning Solution over night before fixing them back.

    Small hiccup forced me to paused for around half an hour as the Retaining Clip for the Bearing flew off to nowhere. Fortunately it was found and the Bearing was reinstalled properly.

    The end result was remarkable as the Spool is spinning smoothly again, it would perform better after the fishing line is replaced and aligned in order.

    In part 5 as well as the final installment, I put back everything and the Daiwa Millionaire Proteus 300 is ready to be upgraded to the next level. It will be fitted with the DIY Mono Mag which will be featured in the DIY Mono Mag series. So, don't touch that dial and stay tuned on this channel. 

==============================­­========­==­­=====
Please give me your valuable comments to help me making improvement and click the LIKE and SHARE if you find the video is good. Subscribe to my channel for the latest update on the new videos.

You can reach me @

NorthernHardcoreFisherman @ Google+

NorthernHardcoreFisherman @ Facebook

NorthernHardcoreFisherman @ Instagram

NorthernHardcoreFisherman @ Twitter

NorthernHardcoreFisherman @ Tumblr

==============================­­========­==­­=====
Always Tight Line, Hardcore is the Spirit!

Read More